Experimental Training Equipments-> Microwave Trainers

[1]   Click to Enlarge SATELLITE COMMUNICATION RECEIVER TRAINER Lab Satellite Communication Receiver Trainer is highly advanced version. After studying this demonstrator the student will have thorough knowledge of Satellite Communication Receiver. The objectives of using this trainer are: 1. Where it is useful 2. Why it is used 3. The reason of using high frequency for communications via Satellite 4. Reception of down link signal frequencies 5. Parts of dish antenna 6. LNB mounting arrangement 7. Faults due to dish antenna, co-axial cable, LNB 8. Assembling the dish antenna 9. Alignment of dish antenna 10. Receiver circuit description. The block diagram of the Satellite Communication Receiver is printed on the front panel of the trainer. All necessary test points are provided to observe various signals at different stages. Controls like Vision IF, gain control, and volume control are provided on the trainer. DESCRIPTION OF SATELLITE RECEIVER The main function of receiver is to select a particular channel in the converted block of frequencies between 950-1450 MHz and separate the audio and video information. The audio and video cut sockets are provided at the back of the receiver. Generally, an internal modulator is incorporated in the receiver which modulates the audio and video information giving the modulated RF output . The receiver consists of the following stages: 1.Tuner 2. IF Stage i LC Network ii 70 MHz Filter iii IF gain control iv IF Amplifier 3. Detector + Amplifier i. Frequency Demodulator ii. Comparator iii Low Pass Filter 4. Video Amplifier i. High Pass Filter 5. Audio Detector 6. Audio Amplifier 7. Polarator Block 8. Power : 230V AC-MAINS OPERATED Lab Satellite Communication Trainer comes with detailed Instruction Manual, with step by step Procedure, dish antenna and colourTelevision receiver DIMENSION: Dish Antenna-6feet Satellite Receiver Trainer -82cmsx19cmsx48cmx Colour TV 20" with Remote Control SPECIFICATION OF COLOUR TV RECEIVER 1. Receiving System : CCIR B/G 2. Colour Receiving System PAL & NTSC-PLAY BACK 3. Receiving Channels VHF-Low :Ch 2-4 VHF-High :Ch 5-12 VHF :Ch 21-69 Tuner :Hyperband 4. Picture Tube : 53.5 cm, 90 degree Deflection 5. Antenna Input Impedance : 75 OHMS, Unbalanced 6. Speaker : 3" 5", 16 Ohms, 2 pcs 7. Sound Output : 30W PWPO 8. Audio/Video/Input/Output Terminals : Audio input/output. Level 500m Vrms Impedance 30 K Ohms Video Input/Output level 1.0V p-p, 75 Ohms Unbalanced (Composite Video Signal, Sync-negative) 9. Power Requirement : AC 220V, 50Hz (Regulation Range 160V to 270 AC) 10. Power Consumption : 80W (Max) 11. Remote Control : Volume, channel selection, MENU (Volume, Brightness, Contrast, Colour) 12. Controls : TV/AV ASAM (Auto search, Auto Memory) MENU (Brightness, Contrast, Colour) VOLUME PROGRAMME (Channel select) (These specifications are subject to change without notice) (These specifications are subject to change without notice) See Enlarge Click to Enlarge MICROWAVE COMMUNICATION TRAINING SYSTEM DESCRIPTION: The lab Microwave communications training system provides a complete hands-on course of study in the principles of microwave communications. Supplied with a laboratory manual containing both theory and practical exercises contains all the necessary hardware to allow students to explore the real-life application and limitations of microwaves. The practical exercises and assessments contained in the laboratory manual help students to understand how physical phenomena such as INTERFERENCE, PROPAGATION, AND ABSORPTION of microwaves can have serious effects upon the performance of communications systems. TOPIC AREAS: 1. Introduction to microwaves. 2. Measuring the microwave signal and Klystron tube characteristics 3. Reflection of microwaves. 4. Radio signal propagation. 5. Standing wave measurement. 6. The advantages of using wave guide. 7. Wave guide experiment. 8.Microwave behavior in a dielectric. This Trainer comes with klystron power supply klystron tube with mount Variable attenuator Direct reading frequency meter. Slotted station with tunable probe. etc See Enlarge Click to Enlarge RADAR TRAINING SYSTEM Radar Training Kit is a comprehensive trainer comes with all necessary microwave components. In this trainer, all importance has been given to understand the basic principles of radar operation. The detailed Instruction Manual will be supplied along with the trainer. System consists of a micro wave and modulator followed by a variable attenuator and transmit antenna in form of horn. Target is a metallic reflector. The receiver consists of horn antenna and detector pulse from modulator is applied to CRO. The returned reflected signal is also applied to CRO to measure time delay of returned signal. SYSTEM COMPONENTS: KLYSTRON power supply KLYSTRON TUBE - Non Tunable detector mount VAR. ATTENUATOR 30 dB HORN ANTENNA DETECTOR CRO TARGET PLATE CABLES MINIMUM DISTANCE BETWEEN OBJECT AND RADAR 500 M (USE ROOF TOP IN CAMPUS) LIST OF EXPERIMENTS: Measurement of Distance of an object (Reflector) Observe effect of Pulse width and PRF in Radar Observe effect of Object in motion Study of Target signatures with radar absorbing objects See Enlarge [1] Go to Top