Experimental Training Equipments-> Wireless Communications

[1]   Click to Enlarge AM BROAD CAST TRANSMITTER KIT This trainer can track the following aspects: Great for transmitting your tape deck, CD player or voice throughout the building. Easily tunes to any clear channel on the AM broadcast band-from 530 to 1750 KHz Demonstrator the principle of commercial transmitters as well. Superior performance transmits upto - 1 mile. Adjusting input level-can be configured form line level or Microphone input. Operator on 9-12 VDC Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge RF TRANSMITTER This trainer is LC based 300 MHz AM RF transmitter board. It is ideal for almost any application needing an wireless control system. When used with the TX-01 Encoder motherboard, RE-99 receiver board and RE-01 decoder mother board. This generates 4 bits of data providing about 16 different codes 8 bits of address ensures that data sent from this transmitter are passed on to the RE-01 data o/ps, and all stray are rejected. The 8 bit address also allows the use of upto 256 individually addressed receivers to the used with single transmitter. This trainer operates on 5V DC with an operating current of 1.6 mA, at an frequency range of 300 MHz uses LC based AM circuitry. The application are as follows. a. Garage Door opener. b. Remote Data acquisition. c. Car alarm/key less entry. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge ALL BAND HF, VHF, UHF, ACTIVE ANTENNA This trainers teaches the following operations of an Active Antenna. Great for perking up scanner reception. Dual pre-amp HF, VHF/UHF front panel switching. This circuit based on true active antenna research. Performance rival units costing many times more. Front panel RF gain controls. Uses dual gate MOSFET technology for low noise HF amplification and a high gain microwave transistor for VHF/UHF. Includes internal telescopic whip antenna plus auxiliary antenna input jack for jazzing up existing antennas. Informative manual comes along with the trainer.   Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge RADAR SIGNAL DETECTOR This trainer uses dual op-amp and super tiny amp to detect traffic violations. This trainer responds only to modulated signals. This operates on +9V dc. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge TELEVISION TRANSMITTER KIT This trainer demonstrates the following operation. Watching one VCR from only where on the house. Using cam coder camera to watch remote areas. Hidden camera fun. Home TV station. Student TV station. This trainer operates on Runs on 12 to 15 DC On board whip Antenna. Stable output adjustable to channel 3-6. Clear, Concise, Step-by-step instructions. Video and Audio I / p compatible with any VCR or TV camera Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge MICROWAVE MOTOR DETECTOR Trainer This trainer demonstrator the following aspects. a. True microwave Doppler shift operation. b. Unaffected by heat, light, sound, humidity (or) temperature. c. A real microwave transmitter/receiver-runs at/GHz. d. Operates on 9-15 DC-ideal for can burglar alarm. e. An informative manual answers questions on Theory. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge PIXIZ QRP TRANSCEIVER Trainer This trainer is a CW transceiver kit with a range of 16-160 meters (80m-optional with an RF output of 200-300 mw. 8W speaker is used as audio o/p. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge INFRARED TRANSMITTER KIT This trainer uses IC 555 timer to pulse an infrared Led. This IC is connected as an astable multivibrator (oscillator) that has a frequency determined by RFC Values. The battery charges capacitor C1 through Resistor R1. When push button is pressed, the Direct Current (DC) charge is applied to the input of the IC causing it to pulse the infra-red LED for about 1-sec. This pulse is actually a series of light pulses occurring in the 1-sec time inferred. Frequency if the pulse is determined. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge Click to Enlarge FM-WIRELESS MIKE TRAINER This trainer demonstrates the following functions. Wireless transmission upto 300-feet. Tune 88-108 MHz FM band. Picks up normal room conversation 10 feet away. This trainer requires 2-15V DC This trainer comes with detailed manual and instruction. Dimension: 27cms x 17cms x 10cms Weight: (Approx.) 500GMS Power: 230VAC Mains operated See Enlarge [1] Go to Top