Quality Control Laboratory Equipments-> Strength of Materials

[1] [«Back ||Next »]   Click to Enlarge Computerized Universal Testing Machine The machine strictly conforms to IS 1828 is designed for testing metalsand other materials under tension, compression, bending / Transverse loads. It is computerized and incorporates Germen scada software with logic controller of Fanue. This computerized Universal Testing Machine is supplied complete with PC,Monitor, 104 Keys Key Board,Logitech Mouse. The electronics come in a rugged and dust protected IP 68 enclosure. Features Automatic data capture,storage and graphic display. Recording storage and retrieval of results and details. Real time monitor display to allow Operation/system interaction. Auto load ranging. On line display of load/extension characteristics. Tare load ,peak hold and reset elongation facilities shall be available. See Enlarge Click to Enlarge Torsion Testing Machine We give below the salient features of the machines for your kind perusal. In our machine a round specimen can be held between the gripping jaws without their ends being machined to a square form, which is a unique feature in our Machine. The gripping jaws provided are 'Talon-Claw' dual gripping system, which Ensures proper gripping without any chance of slippage. In other makes, this feature is not available. In their machines, a square rod is Machined from the center to form round and either ends are in square form, to Fit onto the square slot on either ends of the gripping jaws. Square specimens are quite expensive and machining it in the center to round Form is time consuming and laborious. See Enlarge Click to Enlarge Universal Testing Machine The machine is designed for testing metals and other metals and other materials under tension, compression, bending/transverse loads. The machine is operable on 415 volts, three phase 50 hz ac supply and based on the rated capacity of the machine, has four load measuring ranges, as quoted below against each rated capacity of the machine. An autographic continous roll load elongation recorder, incorporated in the machine products a graph of load vs elongation. Standard Accessories For Conducting Tension Tests : Clamping jaws for testing Round and Flat test specimens under Tension Tests. For Conducting Compression Tests: A PAIR OF compression Platens, duly hardened, ground and polished, with the bottom platen provided with guide-lines for placing the test specimen co-axial with the hydraulic RAM. For Conducting Bending/ Transverse: A table with adjustable rollers complete with mandrel for conducting bending/Transverse Tests See Enlarge Click to Enlarge Pendulam Impact Testing Machine The machine strictly confirms to the relevant IS Standards and is designed for conducting IZOD & Charpy Tests on metals and alloys. The machine is supplied complete with strikes for conducting IZOD and Charpy Tests. Optional Accessories : Caliper gauge for checking V notch for Izod & Charpy as per BS:131:PART:1,2,3. Depth notch gauge including V & U notch, angle & radius Self centering tong. V-notch milling cutter. U-notch milling cutter See Enlarge Click to Enlarge Rockwell Hardness Tester The machine is designed for conducting Rockwell Hardness Tests under A,B and C Scales. The machine is supplied complete with ball and Diamond Indentors and Test blocks for HRB & HRC. Capacity : 185 KGF See Enlarge Click to Enlarge Rockwell Cum Brinell Hardness Tester The machine is combined version, wherein both Rockwell Hardness under A,B and C Scales and Brinell Tests can be conducted. The machine is supplied complete with ball and diamond indentors together with Test Block for HRB and HRC Scales and Ball Indentor for Brinell Hardness test together with an illuminating type Brinell microscope complete with a BHN Conversion Table. Capacity: 250 KGF Technical Data Loads 60,100,150,187.5, 250 Initial Load 10 Max. Test height 230 Depth of Throat 133 Max. Depth of elevating screw below base 240 Size of Base (approx) 171x423 Machine Height 635 Net. Weight (approx) 75kg See Enlarge Click to Enlarge Brinell Hardness Tester 3000 Kgf Capacity 3000 Kgf Capacity Manually Operated & Manual cum Electricity operated B3000 (J) Brinell Hardness Tester 3000 Kgf. Model AI B-3000(J) : Simplest model of Brinell Hardness tester with mechanical Design. Loading, unloading manual, Best suitable for testing batch quantities. B-3000(H) Brinell Hardness Tester 3000 Kgf. Model AIB-3000(H) : Machine designed with a hydraulic power pack and control circuit for effortless loading unloading operation. A dial gauge in front measures depth of ball penetration. This facilities production testing within tolerance limits by compression method. B-3000(0) Brinell Hardness Tester 3000 Kgf. Model AIB-3000(O) : Basic machine design and operation similar to AIB-3000(H). In addition, an ?optical device? with 14x magnification provided in front to project data of ball impression on glass screen with a micrometer measuring system with 0.01 mm accuracy. This indenter swivels and projects dia of ball impression immediately after unloading operation which avoids additional time for measurement of ball impression. This gives real Brinell number on production testing. See Enlarge Click to Enlarge Fatigue Testing Machine For metals: Reserve Bending, Cantilever type supplied complete with jigs and fixtures mounted an elegant table with motor, weights, etc. Features: This machine is used to test the Fatigue strength of materials and to draw S-N diagram by research institutes, laboratories, material manufacturers and various industries. This is a rotating beam type machine in which load is applied in reversed bending fashion. The standard 8 mm dia specimen is held in special holders at its ends and loaded such that it experiences a uniform bending moment. The specimen is rotated at 4200 rpm by a motor. A complete cycle of reversed stresses in all fibres of the specimen is produced during each revolution. The bending moment is applied with a lever system and can be easily changed by moving a weight over the lever. Total number of revolutions at which the specimen fails are recorded by a Digital counter. An interlocking system puts off the motor at specimen failure. Machine meets requirements of IS 5075-1969 Technical Specifications: Maximum bending momentkg cm 200 Bending moment adjustable kg cm25-200 Ranges I-kg cm 25-125 II-kg cm 125-200 Gripping dia of specimen mm 12 Testing dia of specimen mm 8 Rotating Speed rpm 4200 Accuracy of applied bending moment. Digital counter No. of digits 8 Power required HP 0.5 Main supply 3ph,440,V,50Hz,A.C. Overall Size (approx)mm 1000 L.X. Weight (approx.)kg 120 See Enlarge Click to Enlarge Tensile Testing Machine The machine is designed for determining Tensile Strength and Elongation Properties of a variety of materials. Each machine based on its rated capacity has 3 Load Ranges as detailed against each capacity quoted. The machine is operable on 415 volts, 3 phase 50 Hz AC supply and is supplied complete with one set of grips for holding the specimen under test. The detailed specifications of the machine is as per our enclosed leaflet. A. Capacity : 50 Kgf Load Ranges : 0 - 50 Kgf X 100 Gms 0 - 25 Kgf X 50 Gms 0 - 10 Kgf X 20 Gms B. Capacity : 100 Kgf Load Ranges : 0 - 100 Kgf X 200 Gms 0 - 50 Kgf X 100 Gms 0 - 25 Kgf X 50 Gms C. Capacity : 250 Kgf Load Ranges : 0 - 250 Kgf X 500 Gms 0 - 100 Kgf X 200 Gms 0 - 50 Kgf X 100 Gms D. Capacity : 500 Kgf Load Ranges : 0 - 500 Kgf X 1 Kgf 0 - 250 Kgf X 500 Gms 0 - 100 Kgf X 200 Gms E. Capacity : 1000 Kgf Load Ranges : 0 - 1000 Kgf X 2 Kgf 0 - 500 Kgf X 1 Kgf 0 - 250 Kgf X 500 Gms F. Capacity : 2500 Kgf Load Ranges : 0 - 2500 Kgf X 5 Kgf 0 - 1000 Kgf X 2 Kgf 0 - 500 Kgf X 1 Kgf G. Capacity : 5000 Kgf Load Ranges : 0 - 5000 Kgf X 10 Kgf 0 - 2500 Kgf X 5 Kgf 0 - 500 Kgf X 2 Kgf H. Capacity : 10000 Kgf Load Ranges : 0 - 10000 Kgf X 20 Kgf 0 - 5000 Kgf X 10 Kgf 0 - 2500 Kgf X 5 Kgf See Enlarge Click to Enlarge Erichsen Cupping Tester The equipment is designed to reveal the cupping qualities of metal sheets and strips. It can also be used for testing adhesion, elasticity and porosity of coats of paints or varnish by way of comparison. The material after fracture gives in grain structure and contitution. Features: The big handle and the intermediate gearing provided make easy pressing and swelling out of the charged sheet metal by the punch. It is easy to get the pointer to zero as the top of punch and furrow holding plane are always kept to coincide by measurement correction panel. A necessary tolerance, 0.05mm is obtained by the rear back screw, easily and precisely. By utilizing the attached test piece holders, suitable tests for nos. 1,2 and 3 test pieces, can be easily performed at the most normal location. Installation: It is recommended that the machine is mounted on a table. It reserves rights of change in the above specification due to constant improvement in design. The dimensions given above are all approximate. Erichsen tester is designed to carry out Erichsen Cupping test on metals. Quick clamping and manual operation facilitates faster and trouble free working of the machine. See Enlarge Click to Enlarge Wire Wrapping Tester As per IS 1716, the machine is designed for conducting bend test on steel wires of major dimensions from 0.8mm to 5mm. The test is conducted by repeat bending of test piece to rupture over a cylindrical surface of specified radius through 90 degrees consists of a base plate on which a complete arrangement for conducting bend test on wires. The machine comes in assembled ready-to-use condition. Manaually operated upto 4mm dia wires Electrically operated upto 10mm dia wires See Enlarge Click to Enlarge Compression Testing Machine The machine is designed for determining the compression strength of cement concrete cubes upto 200mmx200mm and cylinders of size upto 200mm dia x 300mm height. The machine is hydraulically operated and are available in manually operated version and manual cum electrically operated versions. We are quoting below our prices for both the versions and the types on our range of manufacture: Capacity 100 Tonnes : Manually Operated Channel type loading Unit Same as above but both Manual cum Electricity operated Capacity 200 Tonnes: Electrical Operated : Channel Typoe Loading Unit With Single Hydraulic Pressure Gauge Reading 0 - 200000Kgf X 1000Kg Same As Above But With 2 Hydraulic Pressure Gauges Reading 0 - 200000Kgf X 1000Kg And 0 - 100000Kgf X 500Kgf Divisions Same As Above But With 3 Hydraulic Pressure Gauges Reading 0 - 20000 Kgf X 1000 Kgf; 0 - 100000 Kgf X 500 Kgf And 0 - 50000 Kgf X 250 Kgf Divisions Capacity: 300 Tonnes: Electrically operated with Single Hydraulic Pressure Guage reading 0 - 300000 Kgf x 1500 Kgf Same as above but with 2 Hydraulic Pressure Gauges reading 0 - 300000 Kgf X 1500 Kgf and 0 - 200000 Kgf x 1000 Kgf divisions Same as above but with 3 Hydraulic Pressure Gauges Reading 0 - 300000 Kgf x 1500 Kgf; 0 - 100000 x 1000 Kgf and 0 - 100000 Kgf x 500 Kgf divisions Note: If any of the above quoted 200 Tonnes Compression Testing Machines are required in Two Pillar Compression Type Models See Enlarge Click to Enlarge Spring Testing Machine Foreward The equipment is designed for testing Tension and compression Springs. Description: The machine consists of a robust base on which two columns are fitted with a contraption for holding Tension springs with a rotating handle and a pair of Compression Platens for Compression Springs. A Mechanical Graduated 0-1000 kgf is provided on top that indicates the load against a pointer. All the Steel columns are Electro plated & the shell is powder coated. Technical Specifications: ? Maximum load capacity -50kg ? Resolution of load measurement - 0.2 kg ? Resolution of Deflection measurement ? 1mm ? Overall Size (l x b x h ) - 500mm x 300mm 1500mm ? Overall weight - 60 kg (approx) ? Stiffness of the Spring both closed and open coil can be found out using same experiment. See Enlarge Click to Enlarge Vickers Hardness Tester Vickers Hardness Tester is simple & accurate in design. It is Suitable for measuring the hardness of precision metallic parts with wide testing range from soft to hard & their accurate results are widely acclaimed. These testers strictly conform to IS” 1754 part I & part II 1986. Features: Wide testing range from soft metal such as lead, up to the hardest, like hardened steel. Tiny indentation allows testing of a precision finished parts. Thin sheet metal are perfectly tested. Because applied load is very small Same Hardness number is obtained on the same specimen, regardless of the load applied. Motorized loading and unloading cycle.§ Built-in projection screen to get accurate results. Technical Data: Test Loads : 5, 10, 20, 30, 50kg Magnification of optical projection : 70x Max.Test Height (mm). : 200 Scale least count (mm). : 0.001 Depth of throat (mm). : 133 Dimensions of machine (mm) : L585xW290xH860 Weight (Approx) : 73kg Power Supply : 220v AC, 50Hz, 1-phase Standard Accessories: Standard Test Block : 1 pc. Diamond Penetrator : 1 pc. Weights : 1 Set. Flat Anvil : 1 pc. Vee-type Anvil (Small and Big) : 1 pc. Each Spanners : 1 set Electric cord : 1 pc Instruction Manual : 1 book See Enlarge Click to Enlarge Micro Vickers Hardness Tester ?The system would be used for measuring microscopic hardness in micro Vickers of metals/alloys, various phases/micro-constituents present in metal matrix, thin wires & sheets, diffusion coatings and case depth of carburised/ nitride components etc. Features: A low cost upto-mechanical instrument which can be used for measuring microscopic hardness in micro Vickers. The instrument comprises of a microscope with a filar micrometer eye piece mounted on a stand, loading and unloading mechanism attached to the microscope for taking an indentation of a diamond indenter on a specimen surface under certain load in gms, an illumination system mounted on the microscope and rotating table having X and Y movements. Specifications: Viewing system Objective 40x Micrometer eyepiece 10x Total magnification 400x Working distance -1mm Illumination system Lamp (6V,20W halogen) Fitted with condenser, filter, Iris diaphragm and Power supply through transformer from230 Volts, AC, 50 Hz IndentationsystemLoading/UnloadingMechanismWeights 10 to 200 gm Indenter Diamond Pyramid with an angle of 136 degreeRange 80 to 1000 VickersAccuracy +/- 20 Vickers Specimen Table Angle of turn 0 to 180 degree Longitudinal travel 0 to 100mm Crosswise travel 0 to 10mm Micrometer feed scale 0.01mm/div Total weight of the System 20kgs (approx) Dimensions 340x290x380mm (approx) See Enlarge [1] [«Back ||Next »] Go to Top